CO2 Adsorption on Pore-Engineered Carbons Derived from Jute Sticks.

CO2 capture is a practical approach to mitigating the impacts of global warming. Adsorption-based carbon capture is a clean and potentially energy-efficient method whose performance greatly depends on adsorbent design. In this study, we explored the use of jute-derived carbon as a high-performance adsorbent for CO2 capture. The carbons were produced by pyrolyzing powdered jute sticks with NaHCO3 as an activating agent at 500-700 °C. Impressive adsorption capacities of up to 2.5 mmol ⋅ g-1 and CO2 /N2 selectivities of up to 54 were achieved by adjusting the pore size distribution and surface functionalization. Based on the isotherm results, the working capacities, regenerabilities, and potentials for CO2 separation were determined for a practical vacuum swing adsorption process. The adsorbent materials were characterized by XRD, FTIR, Raman, FESEM and N2 sorption at 77 K. This study provides a general approach for designing adsorbents for various gas-separation applications.

Preparation of Highly Stable and Electrochemically Active Three-dimensional Interconnected Graphene Frameworks from Jute Sticks.

Over the past few years, the environmentally friendly synthesis of nanomaterials, including graphene using green chemistry, has attracted tremendous attention due to its easy handling, low cost, and biocompatibility. Here we demonstrate a facile and efficient green synthesis route for producing highly stable and electrochemically active three-dimensional interconnected graphene frameworks (3DIGF) from jute sticks. Initially, jute sticks derived three-dimensional amorphous activated carbon nanosheets (3DAACNs) were prepared at low temperatures (i. e., 850 °C) in an inert environment. The resultant 3DAACNs were then heat treated at a high temperature (i. e., 2700 °C) under an inert environment, resulting in 3DIGF. The prepared carbonaceous materials were fully characterized, and various experimental techniques confirmed the preparation of 3DIGF. The prepared 3DIGF shows a highly stable nature in thermal and chemical environments and demonstrates a highly dynamic nature for the electrooxidation of sulfide. This study could be considered a vital contribution towards the economic and simple approach for preparing 3DIGF from biomass.

Date-Leaf Carbon Particles for Green Enhanced Oil Recovery.

Green enhanced oil recovery (GEOR) is an environmentally friendly enhanced oil recovery (EOR) process involving the injection of green fluids to improve macroscopic and microscopic sweep efficiencies while boosting tertiary oil production. Carbon nanomaterials such as graphene, carbon nanotube (CNT), and carbon dots have gained interest for their superior ability to increase oil recovery. These particles have been successfully tested in EOR, although they are expensive and do not extend to GEOR. In addition, the application of carbon particles in the GEOR method is not well understood yet, requiring thorough documentation. The goals of this work are to develop carbon nanoparticles from biomass and explore their role in GEOR. The carbon nanoparticles were prepared from date leaves, which are inexpensive biomass, through pyrolysis and ball-milling methods. The synthesized carbon nanomaterials were characterized using the standard process. Three formulations of functionalized and non-functionalized date-leaf carbon nanoparticle (DLCNP) solutions were chosen for core floods based on phase behavior and interfacial tension (IFT) properties to examine their potential for smart water and green chemical flooding. The carboxylated DLCNP was mixed with distilled water in the first formulation to be tested for smart water flood in the sandstone core. After water flooding, this formulation recovered 9% incremental oil of the oil initially in place. In contrast, non-functionalized DLCNP formulated with (the biodegradable) surfactant alkyl polyglycoside and NaCl produced 18% more tertiary oil than the CNT. This work thus provides new green chemical agents and formulations for EOR applications so that oil can be produced more economically and sustainably.

Physico-chemical properties and toxicological effects on plant and algal models of carbon nanosheets from a nettle fibre clone.

Carbon nanosheets are two-dimensional nanostructured materials that have applications as energy storage devices, electrochemical sensors, sample supports, filtration membranes, thanks to their high porosity and surface area. Here, for the first time, carbon nanosheets have been prepared from the stems and leaves of a nettle fibre clone, by using a cheap and straight-forward procedure that can be easily scaled up. The nanomaterial shows interesting physical parameters, namely interconnectivity of pores, graphitization, surface area and pore width. These characteristics are similar to those described for the nanomaterials obtained from other fibre crops. However, the advantage of nettle over other plants is its fast growth and easy propagation of homogeneous material using stem cuttings. This last aspect guarantees homogeneity of the starting raw material, a feature that is sought-after to get a nanomaterial with homogeneous and reproducible properties. To evaluate the potential toxic effects if released in the environment, an assessment of the impact on plant reproduction performance and microalgal growth has been carried out by using tobacco pollen cells and the green microalga Pseudokirchneriella subcapitata. No inhibitory effects on pollen germination are recorded, while algal growth inhibition is observed at higher concentrations of leaf carbon nanosheets with lower graphitization degree.